Not Optimum Mode error

[markoca]

U poslednje vreme moj SM 2043NW zna da zapuca i da prikaze error "Not Optimum Mode. Recommended mode: 1680x1050 60Hz". Ovo se desava samo u igrama. Lecim gasenjem i paljenjem racunara, a problem i dalje ostaje.
Koristim 1680x1050 rezoluciju. I u igrama i na desktopu.

????

[Doomche]

Koju grafichku karticu koristish? Da li si instalirao drajvere za monitor, odnosno podesio refresh rate na 60Hz, a ne vishe?

[markoca]

MSI R4850 T2-D512 je u pitanju, refresh rate je na 60Hz. Softver za monitor je instaliran (MagicTune i pratece alatke, to sam nasao na CD-u). Nedavno sam poceo da dobijam taj error, nema ni mesec dana.

[markoca]

Jel postoji neko resenje za ovo? Gledam na netu, mnogi imaju taj problem...

[Doomche]

Gledah i ja sad na netu, problem je definitivno do monitora, izgleda da se svakom LCD modelu mozhe desiti. Potezhi garanciju, koliko videh Samsung ce to odmah zameniti.

[markoca]

Prvi put mi se desilo u Call of Juarez Bound in Blood, a iskace svakih 10 minuta u Bionic Commando, i u jos nekim igrama...

[Freško]

Check the signal cable connection. (Connected using the DVI cable) If you still see an error message on the screen when the monitor is connected properly, check to see if the monitor status is set to analog. Press SOURCE/ button to have the monitor doublecheck the input signal source. If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card. (Refer to the Preset Timing Modes) If the initial screen (the login screen) does not appear, contact the Service Center or your dealer. If the power is on, reboot the computer to see the initial screen(the login screen), which can be seen.

Can you see “Not Optimum Mode”, “Recommended Mode 1680 X 1050 60 Hz” on the screen? You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly. Adjust the maximum resolution and frequency that the monitor can handle properly. If the display exceeds SXGA or 75 Hz, a “Not Optimum Mode”, “Recommended Mode 1680 X 1050 60 Hz” message is displayed. If the display exceeds 85 Hz, the display will work properly but the “Not Optimum Mode”, “Recommended Mode 1680 X 1050 60 Hz” message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.) There is no image on the screen. Is the power The monitor is in PowerSaver mode. Press a key on the keyboard to activate the monitor and indicator on the monitor blinking at 1 second intervals? restore the image on the screen. If there is still no image, press the ‘SOURCE/ ‘ button. Then press any key on the keyboard again to activate the monitor and restore the image on the screen. You may get a blank screen if you boot the system before you connect the DVI cable, or disconnect and then reconnect the DVI cable while the system is running as certain types of graphic cards do not send out video signals. Connect the DVI cable and then reboot the system. Unlock the OSD by pressing the [MENU / least 5 seconds. ] button for at Connected using the DVI cable? I cannot see the On Screen Display. Have you locked the On Screen Display (OSD) Menu to prevent changes? Is the screen displaying only one color as if looking at the screen through a cellophane paper? Have the screen colors become strange after running a program or due to a crash between applications? Has the video card been set properly? The screen shows strange colors or just black and white. Check the signal cable connection. Make sure the video card is fully inserted in it’s slot. Reboot the computer. Set the video card by referring to the video card manual.

Izvor

[markoca]

OK...

-nemam dvi kabel, 2043nw.....
-gde je source/ taster?


sve drzim na 60hz i 1680x1050....pu sunce mu....