|
Kvarovi Pomoć i informacije u vezi sa neobjašnjivim kvarovima i nestabilnostima sistema |
|
Alatke vezane za temu | Vrste prikaza |
17.5.2012, 22:50 | #1 |
Starosedelac
Član od: 9.7.2010.
Lokacija: N/A
Poruke: 1.795
Zahvalnice: 750
Zahvaljeno 536 puta na 369 poruka
|
Nakon BSODa ne radi HDD
Dok igram igre ili radi neki jaci proces, desasva se da izbije BSOD, kompjuter se restartuje i pri ponovnom paljenju ne cita HDD tj pojavi se
Onda moram da restartujem komp i tek onda radi kako treba. Ali nakon BSODa , kad ponovo udejm u neku igru, nakon nekog vremena igra ubaguje, sve se zamrzne a mis radi, tj mogu da pomeram strelicu dok je sve ostalo zamrznuto... Testirao sam RAM i nema problema, temp su ok... |
17.5.2012, 22:59 | #3 |
V.I.P. Test Drive
Član od: 16.2.2011.
Poruke: 2.712
Zahvalnice: 41
Zahvaljeno 813 puta na 699 poruka
|
Re: Nakon BSODa ne radi HDD
Ili je hard disk na samrti.
|
17.5.2012, 23:09 | #4 |
Deo inventara foruma
|
Re: Nakon BSODa ne radi HDD
Vrlo moguće, ja bih kao alternativu probao kuler sa dva venta koji idu ispod hard diska da bi se lakše ohladio, to sve izgleda ovako
|
17.5.2012, 23:33 | #5 |
Starosedelac
Član od: 9.7.2010.
Lokacija: N/A
Poruke: 1.795
Zahvalnice: 750
Zahvaljeno 536 puta na 369 poruka
|
Re: Nakon BSODa ne radi HDD
Vec imam jedan vent kod HDDa...
U speeciu mi pokazuje da je temp harda manja od 25c. |
17.5.2012, 23:52 | #6 |
V.I.P. Test Drive
Član od: 16.2.2011.
Poruke: 2.712
Zahvalnice: 41
Zahvaljeno 813 puta na 699 poruka
|
Re: Nakon BSODa ne radi HDD
Pogledaj šta kažu S.M.A.R.T podaci sa hard diska.
|
18.5.2012, 0:19 | #7 |
Starosedelac
Član od: 9.7.2010.
Lokacija: N/A
Poruke: 1.795
Zahvalnice: 750
Zahvaljeno 536 puta na 369 poruka
|
Re: Nakon BSODa ne radi HDD
Kod:
01 Read Error Rate 114 (099 worst) Data 0003A8FD6E 03 Spin-Up Time 100 (093) Data 0000000000 04 Start/Stop Count 099 (099) Data 0000000716 05 Reallocated Sectors Count 100 (100) Data 0000000001 07 Seek Error Rate 084 (060) Data 000E4AB7FA 09 Power-On Hours (POH) 089 (089) Data 000000268E 0A Spin Retry Count 100 (099) Data 00000000AB 0C Device Power Cycle Count 099 (099) Data 0000000658 B8 End-to-End error / IOEDC 001 (001) Data 0000000567 BB Reported Uncorrectable Errors 100 (100) Data 0000000000 BC Command Timeout 100 (097) Data 0000020135 BD High Fly Writes (WDC) 001 (001) Data 000000009C BE Temperature Difference from 100 080 (050) Data 0014130014 C2 Temperature 020 (050) Data 0000000014 C3 Hardware ECC Recovered 048 (026) Data 0003A8FD6E C5 Current Pending Sector Count 100 (100) Data 0000000000 C6 Uncorrectable Sector Count 100 (100) Data 0000000000 C7 UltraDMA CRC Error Count 200 (200) Data 0000000000 F0 Head Flying Hours 100 (253) Data 000000267A F1 Total LBAs Written 100 (253) Data 0076FA98E6 F2 Total LBAs Read 100 (253) Data 0053BE7837 Temperature 20 °C Temperature Range ok (less than 50 °C) Status Good |
18.5.2012, 8:01 | #8 |
V.I.P. Test Play
Član od: 5.4.2006.
Lokacija: Beograd
Poruke: 14.772
Zahvalnice: 5.416
Zahvaljeno 4.101 puta na 2.675 poruka
|
Re: Nakon BSODa ne radi HDD
Pretpostavljam, da moze i napajanje da zeza, pa da ima uticaj na HDD.
|
18.5.2012, 19:00 | #9 |
Starosedelac
Član od: 15.10.2010.
Poruke: 1.247
Zahvalnice: 34
Zahvaljeno 183 puta na 176 poruka
|
Re: Nakon BSODa ne radi HDD
Šta kaže Sentinel?
|
19.5.2012, 13:42 | #10 |
Starosedelac
Član od: 9.7.2010.
Lokacija: N/A
Poruke: 1.795
Zahvalnice: 750
Zahvaljeno 536 puta na 369 poruka
|
Re: Nakon BSODa ne radi HDD
Kad se pojavi BSOD izadje Kernel Data Inpage error
|
19.5.2012, 14:03 | #11 |
Deo inventara foruma
|
Re: Nakon BSODa ne radi HDD
Stop 0x0000007A or KERNEL_DATA_INPAGE_ERROR
The Stop 0x7A message indicates that a page of kernel data was not found in the paging (virtual memory) file and could not be read into memory. This might be due to incompatible disk or controller drivers, firmware, or hardware. Frequently, the cause of this error can be determined from the second parameter, the I/O status code. Some common status codes are: # 0xC000009A, or STATUS_INSUFFICIENT_RESOURCES, indicates a lack of nonpaged pool resources # 0xC000009C, or STATUS_DEVICE_DATA_ERROR, indicates bad blocks (sectors) on the hard disk # 0xC000009D, or STATUS_DEVICE_NOT_CONNECTED, indicates defective or loose data or power cables, a problem with SCSI termination, or improper controller or disk configuration # 0xC000016A, or STATUS_DISK_OPERATION_FAILED, indicates bad blocks (sectors) on the hard disk # 0xC0000185, or STATUS_IO_DEVICE_ERROR, indicates improper termination, defective storage controller hardware, or defective disk cabling, or two devices attempting to use the same resources. Possible Resolutions: # Stop 0x7A can be caused by bad sectors in the virtual memory paging file, disk controller error, virus infection, or memory hardware problems. In extremely rare cases, depleted nonpaged pool resources can cause this error. If the first and third parameters are zero, the stack signature in the kernel stack is missing, an error typically caused by defective hardware. If the I/O status is 0xC0000185 and the paging file is on a SCSI disk, check for cabling and termination issues. An I/O status code of 0xC000009C or 0xC000016A indicates that the requested data could not be found. You can try to correct this by restarting the computer. If a problem with disk integrity exists, Autochk, a program that attempts to mark bad disk sectors as defective so that they are not used in the future, starts automatically. If Autochk fails to run, you can manually perform the integrity check yourself by following the instructions to run Chkdsk provided in "Stop 0x00000024 or NTFS_FILE_SYSTEM" earlier in this appendix. # Another cause of Stop 0x7A messages is defective, malfunctioning, or failed memory hardware, such as memory modules, Level 2 (L2) SRAM cache, or video adapter RAM. If you added new hardware recently, remove and replace it to determine if it is causing or contributing to the problem. Run diagnostics software supplied by the system manufacturer to determine if the component has failed. # Check the hardware manufacturer's Web site (hosted on top web hosting server) for updates to disk adapter firmware or drivers that improve compatibility. Verify that your disks and controller support the same set of advanced features, such as higher transfer rates. If necessary, select a slower transfer rate if an update is not yet available. Consult your hardware or device documentation for more information. Important - You can install disk controller drivers not present on the Windows XP Professional operating system CD by responding to the following prompt shortly after starting Setup: - Press F6 if you need to install a third party SCSI or RAID driver. - Press F6, and when prompted, provide the appropriate storage controller driver (ATA or SCSI) supplied by the manufacturer. # The problem might also be due to cracks, scratched traces, or defective components on the motherboard. If all else fails, take the system motherboard to a repair facility for diagnostic testing. # Problems that cause Stop 0x7A messages can also cause Stop 0x77 messages. For more information about Stop 0x77 messages, see "Stop 0x00000077 or KERNEL_STACK_INPAGE_ERROR" earlier in this list. Tekst preuzet odavde a vrijedi i za XP i za sedmicu. |
Sledeći korisnik se zahvaljuje korisniku LoneWolf na korisnoj poruci: | ||
Luka Filipovic (19.5.2012) |
19.5.2012, 14:09 | #12 |
V.I.P. Test Drive
Član od: 16.2.2011.
Poruke: 2.712
Zahvalnice: 41
Zahvaljeno 813 puta na 699 poruka
|
Re: Nakon BSODa ne radi HDD
Hard disk po svemu sudeći riknjava, proveri sata kablove i kablove od napajanja. Ako i dalje nastavi sa istim, najverovatnije ti ne gine nabavka novog hard diska (ili ga reklamiraj ako je pod garancijom).
|
19.5.2012, 14:35 | #13 |
Starosedelac
Član od: 9.7.2010.
Lokacija: N/A
Poruke: 1.795
Zahvalnice: 750
Zahvaljeno 536 puta na 369 poruka
|
Re: Nakon BSODa ne radi HDD
Menjao sam SATA kabal , jedino da probam napajanje da zamenim.
Cim probam javaljm da li se ponovo desava Lonewolf, Izgubio sam se u tom tesktu |
19.5.2012, 15:26 | #14 |
V.I.P. Test Drive
Član od: 16.2.2011.
Poruke: 2.712
Zahvalnice: 41
Zahvaljeno 813 puta na 699 poruka
|
Re: Nakon BSODa ne radi HDD
Sažetak tog teksta:
Stop 0x0000007A or KERNEL_DATA_INPAGE_ERROR koju dobijaš je posledica toga što kompjuter ne može da pročita podatke iz virtuelne memorije, tj. one što je smeštena na hard disku u fajlu pagefile.sys. Uzrok toga je najverovatnije hardver (loši sektori na hard disku, neispravna glava za čitanje, neispravan kontroler) |
Sledeći korisnik se zahvaljuje korisniku SlobaL na korisnoj poruci: | ||
Luka Filipovic (19.5.2012) |
Bookmarks sajtovi |
|
|
Slične teme | ||||
tema | temu započeo | forum | Odgovora | Poslednja poruka |
Ljudi poludeh nece desni kanal da radi :( | mozdani | Zvuk na računaru | 8 | 17.10.2010 14:51 |
Internet ne radi posle "Blue Screen of Death" | Boris Zegarac | Kvarovi | 6 | 6.10.2010 23:52 |
Pomoć - monitor ne radi! | dragutinka | Kvarovi | 15 | 11.9.2010 17:34 |
Neće da radi defragmentacija | - TERMINATOR - | Operativni sistemi | 21 | 4.9.2009 16:48 |
Racunar nece da radi u AHCI modu | harmon | Kvarovi | 10 | 8.8.2007 22:26 |