Nakon BSODa ne radi HDD

[Luka Filipovic]

Dok igram igre ili radi neki jaci proces, desasva se da izbije BSOD, kompjuter se restartuje i pri ponovnom paljenju ne cita HDD tj pojavi se

Onda moram da restartujem komp i tek onda radi kako treba.
Ali nakon BSODa , kad ponovo udejm u neku igru, nakon nekog vremena igra ubaguje, sve se zamrzne a mis radi, tj mogu da pomeram strelicu dok je sve ostalo zamrznuto...
Testirao sam RAM i nema problema, temp su ok...

[LoneWolf]

Zeza te MBR (master boot record) a evo kako da ga središ.

[SlobaL]

Ili je hard disk na samrti.

[LoneWolf]

Vrlo moguće, ja bih kao alternativu probao kuler sa dva venta koji idu ispod hard diska da bi se lakše ohladio, to sve izgleda ovako

[Luka Filipovic]

Vec imam jedan vent kod HDDa...
U speeciu mi pokazuje da je temp harda manja od 25c.

[SlobaL]

Pogledaj šta kažu S.M.A.R.T podaci sa hard diska.

[Luka Filipovic]

01 Read Error Rate				114 (099 worst) Data 0003A8FD6E
03 Spin-Up Time					100 (093) Data 0000000000
04 Start/Stop Count				099 (099) Data 0000000716
05 Reallocated Sectors Count			100 (100) Data 0000000001
07 Seek Error Rate				084 (060) Data 000E4AB7FA
09 Power-On Hours (POH)				089 (089) Data 000000268E
0A Spin Retry Count				100 (099) Data 00000000AB
0C Device Power Cycle Count			099 (099) Data 0000000658
B8 End-to-End error / IOEDC			001 (001) Data 0000000567
BB Reported Uncorrectable Errors		100 (100) Data 0000000000
BC Command Timeout				100 (097) Data 0000020135
BD High Fly Writes (WDC)			001 (001) Data 000000009C
BE Temperature Difference from 	100		080 (050) Data 0014130014
C2 Temperature					020 (050) Data 	0000000014
C3 Hardware ECC Recovered			048 (026) Data 0003A8FD6E
C5 Current Pending Sector Count			100 (100) Data 0000000000
C6 Uncorrectable Sector Count			100 (100) Data 0000000000
C7 UltraDMA CRC Error Count			200 (200) Data 0000000000
F0 Head Flying Hours				100 (253) Data 000000267A
F1 Total LBAs Written				100 (253) Data 0076FA98E6
F2 Total LBAs Read				100 (253) Data 0053BE7837
Temperature					20 °C
Temperature Range				ok (less than 50 °C)
Status						Good

[player1]

Pretpostavljam, da moze i napajanje da zeza, pa da ima uticaj na HDD.

[aconi]

Šta kaže Sentinel?

[Luka Filipovic]

Kad se pojavi BSOD izadje Kernel Data Inpage error

[LoneWolf]

Stop 0x0000007A or KERNEL_DATA_INPAGE_ERROR

The Stop 0x7A message indicates that a page of kernel data was not found in the paging (virtual memory) file and could not be read into memory. This might be due to incompatible disk or controller drivers, firmware, or hardware.

Frequently, the cause of this error can be determined from the second parameter, the I/O status code. Some common status codes are:

# 0xC000009A, or STATUS_INSUFFICIENT_RESOURCES, indicates a lack of nonpaged pool resources

# 0xC000009C, or STATUS_DEVICE_DATA_ERROR, indicates bad blocks (sectors) on the hard disk

# 0xC000009D, or STATUS_DEVICE_NOT_CONNECTED, indicates defective or loose data or power cables, a problem with SCSI termination, or improper controller or disk configuration

# 0xC000016A, or STATUS_DISK_OPERATION_FAILED, indicates bad blocks (sectors) on the hard disk

# 0xC0000185, or STATUS_IO_DEVICE_ERROR, indicates improper termination, defective storage controller hardware, or defective disk cabling, or two devices attempting to use the same resources.

Possible Resolutions:

# Stop 0x7A can be caused by bad sectors in the virtual memory paging file, disk controller error, virus infection, or memory hardware problems. In extremely rare cases, depleted nonpaged pool resources can cause this error. If the first and third parameters are zero, the stack signature in the kernel stack is missing, an error typically caused by defective hardware. If the I/O status is 0xC0000185 and the paging file is on a SCSI disk, check for cabling and termination issues. An I/O status code of 0xC000009C or 0xC000016A indicates that the requested data could not be found. You can try to correct this by restarting the computer. If a problem with disk integrity exists, Autochk, a program that attempts to mark bad disk sectors as defective so that they are not used in the future, starts automatically. If Autochk fails to run, you can manually perform the integrity check yourself by following the instructions to run Chkdsk provided in "Stop 0x00000024 or NTFS_FILE_SYSTEM" earlier in this appendix.

# Another cause of Stop 0x7A messages is defective, malfunctioning, or failed memory hardware, such as memory modules, Level 2 (L2) SRAM cache, or video adapter RAM. If you added new hardware recently, remove and replace it to determine if it is causing or contributing to the problem. Run diagnostics software supplied by the system manufacturer to determine if the component has failed.

# Check the hardware manufacturer's Web site (hosted on top web hosting server) for updates to disk adapter firmware or drivers that improve compatibility. Verify that your disks and controller support the same set of advanced features, such as higher transfer rates. If necessary, select a slower transfer rate if an update is not yet available. Consult your hardware or device documentation for more information.

Important

- You can install disk controller drivers not present on the Windows XP Professional operating system CD by responding to the following prompt shortly after starting Setup:
- Press F6 if you need to install a third party SCSI or RAID driver.
- Press F6, and when prompted, provide the appropriate storage controller driver (ATA or SCSI) supplied by the manufacturer.

# The problem might also be due to cracks, scratched traces, or defective components on the motherboard. If all else fails, take the system motherboard to a repair facility for diagnostic testing.

# Problems that cause Stop 0x7A messages can also cause Stop 0x77 messages. For more information about Stop 0x77 messages, see "Stop 0x00000077 or KERNEL_STACK_INPAGE_ERROR" earlier in this list.

Tekst preuzet odavde a vrijedi i za XP i za sedmicu.

[SlobaL]

Hard disk po svemu sudeći riknjava, proveri sata kablove i kablove od napajanja. Ako i dalje nastavi sa istim, najverovatnije ti ne gine nabavka novog hard diska (ili ga reklamiraj ako je pod garancijom).

[Luka Filipovic]

Menjao sam SATA kabal , jedino da probam napajanje da zamenim.
Cim probam javaljm da li se ponovo desava
Lonewolf,
Izgubio sam se u tom tesktu

[SlobaL]

Sažetak tog teksta:
Stop 0x0000007A or KERNEL_DATA_INPAGE_ERROR koju dobijaš je posledica toga što kompjuter ne može da pročita podatke iz virtuelne memorije, tj. one što je smeštena na hard disku u fajlu pagefile.sys. Uzrok toga je najverovatnije hardver (loši sektori na hard disku, neispravna glava za čitanje, neispravan kontroler)